Hello,
No, we don't have any explicit documentation on this. I think that the
fault-only-first are the few instructions that are not implemented.
Cheers,
Jason
On Thu, Aug 3, 2023 at 10:25 PM X BJ xbj0220ok@outlook.com wrote:
Hello,
Thank you very much, it is exactly what I need !
BTW, is there a instruction list that supported ? Because I notice that
vector load unit-stride fault-only-first is not supported, I'm wondering if
there is a list/site/doc about instructions and other stuff in RVV 1.0.
Thanks again !
Best regards
xbj
发件人: Jason Lowe-Power jason@lowepower.com
发送时间: 2023年8月3日 22:33
收件人: The gem5 Users mailing list gem5-users@gem5.org
抄送: 谢 佰杰 xbj0220ok@outlook.com
主题: Re: [gem5-users] RISCV Vector Extension in gem5
Hello,
Initial RVV support was just merged today! See
https://github.com/gem5/gem5/pull/83
On Thu, Aug 3, 2023 at 12:29 AM 谢 佰杰 via gem5-users gem5-users@gem5.org
wrote:
Hi all,
I found that both rivosInc and RALC888 used to work on RISC-V Vector
Extension in gem5, but both of them seem to be busy with other things,
leaving gem5-rvv 1.0 undone.
I'm wondering what is the status/plan about RISCV-V Vector Extension in
gem5 ?
Thanks + regards
xbj
- [GEM5-1212] Add RISC-V vector support (RVV) version 1.0 - Jira
(atlassian.net) <https://gem5.atlassian.net/browse/GEM5-1212>
- RALC88/gem5: This is an read-only mirror of the gem5 simulator. The
upstream repository is stored in https://gem5.googlesource.com, code
reviews should be submitted to https://gem5-review.googlesource.com/. The
mirrors are synchronized every 15 minutes. (github.com)
<https://github.com/RALC88/gem5>
gem5-users mailing list -- gem5-users@gem5.org
To unsubscribe send an email to gem5-users-leave@gem5.org
Hello,
No, we don't have any explicit documentation on this. I think that the
fault-only-first are the few instructions that are not implemented.
Cheers,
Jason
On Thu, Aug 3, 2023 at 10:25 PM X BJ <xbj0220ok@outlook.com> wrote:
> Hello,
>
> Thank you very much, it is exactly what I need !
>
> BTW, is there a instruction list that supported ? Because I notice that
> vector load unit-stride fault-only-first is not supported, I'm wondering if
> there is a list/site/doc about instructions and other stuff in RVV 1.0.
> Thanks again !
>
> Best regards
> xbj
>
> ------------------------------
> *发件人:* Jason Lowe-Power <jason@lowepower.com>
> *发送时间:* 2023年8月3日 22:33
> *收件人:* The gem5 Users mailing list <gem5-users@gem5.org>
> *抄送:* 谢 佰杰 <xbj0220ok@outlook.com>
> *主题:* Re: [gem5-users] RISCV Vector Extension in gem5
>
> Hello,
>
> Initial RVV support was just merged today! See
> https://github.com/gem5/gem5/pull/83
>
> On Thu, Aug 3, 2023 at 12:29 AM 谢 佰杰 via gem5-users <gem5-users@gem5.org>
> wrote:
>
> Hi all,
> I found that both rivosInc and RALC888 used to work on RISC-V Vector
> Extension in gem5, but both of them seem to be busy with other things,
> leaving gem5-rvv 1.0 undone.
> I'm wondering what is the status/plan about RISCV-V Vector Extension in
> gem5 ?
>
> Thanks + regards
> xbj
>
>
>
> - [GEM5-1212] Add RISC-V vector support (RVV) version 1.0 - Jira
> (atlassian.net) <https://gem5.atlassian.net/browse/GEM5-1212>
>
>
> - RALC88/gem5: This is an read-only mirror of the gem5 simulator. The
> upstream repository is stored in https://gem5.googlesource.com, code
> reviews should be submitted to https://gem5-review.googlesource.com/. The
> mirrors are synchronized every 15 minutes. (github.com)
> <https://github.com/RALC88/gem5>
>
>
>
>
>
> _______________________________________________
> gem5-users mailing list -- gem5-users@gem5.org
> To unsubscribe send an email to gem5-users-leave@gem5.org
>
>
